Oregon Elevation ToolsOpen Contour Lines on the map →

Terrain · Select a property, draw a box or polygon, or upload a boundary

Contour map for any Oregon property

Make an Oregon contour map for any property from the USGS 3DEP lidar elevation model, at any interval from 1 ft upward, and export them clipped to the taxlot boundary as GeoJSON or KML. For AutoCAD and Civil 3D, Download Data exports DXF in Oregon Statewide Lambert feet, as well as Shapefile, SVG and a print-ready PDF, covering the rectangle around the property.

The usual comparison is the USGS topographic quads. Those show the published USGS topographic map series, where each map sheet uses one fixed contour interval chosen for its terrain — commonly 20 or 40 ft in Oregon’s mountains. This tool generates contours at any interval you choose from the underlying elevation model, and lets you export them. A property contour map at 1 or 2 ft shows the ground at the scale a driveway, a house pad or a drainage plan needs, in the format your designer already uses.

Free to run · pay to download

See the full result on the map free, with no account. Download the contours as GeoJSON and KML here, or as DXF, Shapefile, SVG and PDF from Download Data with a pass: US$29 for 24 hours, US$99 for 30 days or US$399 for 12 months, a one-off payment in US dollars that never renews. Every download on the site is included while the pass lasts.

Open Contour Lines on the map →Pass prices and what’s included

Who uses this

  • Architects and designers. Drop site contours into CAD for concept design.
  • Landscapers. Plan grades, paths, retaining walls and planting from real contours.
  • Owners and builders. Understand the fall across a lot before talking to a surveyor.

When to use it

  • You need site contours for a concept plan, a driveway, drainage or a landscape design.
  • You want contours clipped to a property boundary instead of a whole map sheet.
  • The one fixed contour interval of a USGS topo quad is too coarse for the question.

Tools for your job

Contour Lines is one step in a bigger question. These are the jobs it helps with, and the tools that go with it.

For the job: Excavation, driveways and farm roads

How much digging, and can a driveway or farm road make the grade?

  1. 1.Cut & Fill — Cut and fill in cubic yards to level a pad, at an elevation you set or the one that balances.
  2. 2.Elevation Profile — Grade along a proposed driveway, section by section.
  3. 3.Route Explorer — Finds a line between two points that stays under a maximum grade.
  4. 4.Contour Lines (this tool) — Site contours at 1 or 2 ft to hand to a designer.

For the job: Plans, CAD, GIS and 3D printing

I need the terrain as a file.

  1. 1.Download Data — Contours, a GeoTIFF elevation model, a georeferenced aerial photo or a 3D mesh for printing.
  2. 2.Contour Lines (this tool) — Contours previewed on the map before you export them.
  3. 3.Elevate a File — Adds ground elevation to your own GPX, KML, GeoJSON or CSV points.
  4. 4.Add Elevation — A single spot elevation, for a floor level or a tank.
  5. 5.Terrain Stats — The highest, lowest and mean ground elevation of an area, and how the land is spread between them.

How to use it

  1. Select a property, draw an area or upload a boundary.
  2. Choose the contour interval in feet. Finer intervals mean more lines and a bigger file.
  3. Generate. Contours appear on the map with elevation labels you can toggle.
  4. Pick an export format and download.

Step by step: Mount Hood

We draw contours at a 40 ft interval across Mount Hood’s south slope around Timberline Lodge.

1.Zoom to the area and choose Analyze this view, or select a property. Pick the interval: 40 ft suits a whole mountainside, 1 or 2 ft a building lot.

2.Preview on map traces the USGS 3DEP lidar model. The lines are colored by elevation and labeled in feet.

3.Zoom in and more labels appear. The lines bunch on the steep slopes and spread out on the gentler ground. Export as GeoJSON or KML from the panel, or as DXF, PDF and more from Download Data.

What it showed

  • Tight lines are steep ground. The canyons on either side of the lodge show as sharp V-shaped bends pointing uphill.
  • For a site plan, select just the lot and use a 1 or 2 ft interval.
Try it yourself on Mount Hood →

How it works

The USGS 3DEP bare-earth model is loaded for the area and traced at each contour elevation, in whole feet. Fragments are stitched into continuous lines, simplified slightly so the files stay usable, and labeled with their elevation.

The output resolution follows the size of the area: a building site is traced at the full 3.3 ft per pixel, while a block 7.5 miles on a side is resampled to roughly 39 ft per pixel before tracing.

Reading the results

Closely spaced lines mean steep ground; wide spacing means flat. A closed ring with no lines inside is a knoll or a hollow.

Every contour carries its elevation in feet; the GIS formats add a meters field alongside. DXF files are in Oregon Statewide Lambert, in international feet (EPSG:2992).

Limits and caveats

  • Areas up to 7.5 miles per side.
  • Intervals of a few feet are only meaningful where lidar at 3.3 ft per pixel exists. On the coarser fallback model, about 33 ft per pixel, they trace interpolation, not ground.
  • The terrain is a snapshot from the date the lidar was flown. Grading since then is not shown.
  • The GeoJSON and KML exports in this panel are clipped to a selected property. The DXF, Shapefile, SVG and PDF files come from Download Data, which covers the rectangle around the property instead.

Data and attribution

Results come from the USGS 3D Elevation Program (3DEP) bare-earth elevation model: lidar at 3.3 ft per pixel where it has been flown, and the 1/3 arc-second model, about 33 ft per pixel, elsewhere, with elevations above NAVD 88. The tools with a surface option (Sunlight, Viewshed, Sightline, Object Heights) read DOGAMI’s statewide digital surface model of trees and buildings.

USGS 3DEP elevation data and USGS maps are U.S. Government works in the public domain: you may use the results, including commercially. A credit to the USGS 3D Elevation Program is appreciated, and every file you download carries it. DOGAMI lidar products are published by the State of Oregon; credit "DOGAMI / Oregon Lidar Consortium". County taxlot boundaries are the assessor's GIS data, not surveys, and each county publishes its own disclaimer, shown with the parcel. The aerial basemap is from Esri and follows Esri's terms; it is not included in downloads.

Questions

Can I get contours as DXF for AutoCAD?

Yes. Generate the contours on the map, then export from Download Data as DXF. The file is in Oregon Statewide Lambert, international feet (EPSG:2992); each line sits at its elevation in feet, on a layer named for it, and opens in AutoCAD, Civil 3D and most CAD packages.

What is the finest contour interval?

1 ft. Intervals of a few feet are only meaningful where lidar at 3.3 ft per pixel exists; elsewhere the USGS model falls back to about 33 ft per pixel and the download says so. DOGAMI reports about 99% of Oregon covered by at least one lidar project.

Are these contours good enough for a building permit?

They are good enough for concept design and early conversations. What a permit application needs is set by your county or city; many ask for a survey by a licensed surveyor, who may well use the same lidar as a base. Check with your county.

Ready to try it?

Open Contour Lines on the map →

Free to use, no account. The analysis runs in your browser on public-domain USGS 3DEP data. Downloading the results needs a pass: see pricing.